If items are not picked up one week after the final removal day, your items will be resold - NO EXCEPTIONS!Ĩ. If you cannot pick up on the last day of removal, a $5.00 per day storage fee will apply. We cannot guarantee that the item will be available after the load out unless item is paid for and arrangements are made for pick up on the load out day! Items will only be held for 1 week.ħ. Our descriptions are not a substitute for your inspection. It is the bidder’s responsibility to inspect before bidding, to be certain that the item meets your standards and expectations. Every effort is made to describe the items as accurately as possible. K & C Auctions will ship your items UPS for you. No items will be released until paid for in full. Items that are to be shipped need to be paid for in full before pickup is scheduled. If you are unable to pay for and pickup your items on removal date and time, PLEASE DO NOT BID. No payments or pickups can be made before removal date.ģ. K & C Auctions does not accept any checks!Ģ. Please make all payments to: K & C Auctions. No exceptions! Load out day is not preview day!ġ. $40.00 minimum fee for Non load out day pick ups. Consignor expects items to be picked up on Scheduled load out day. ![]() ![]() Items have to be paid for on the load out day. K & C auctions will not accept personal or business checks Look at the duty cycle and thickness of metal yo plan on welding with it.We accept credit Visa and Mastercard, (Minimum $20.00 credit card transaction), cash, and cashiers checks. Nice thing about the Lincoln from what I have read is the setup to run aluminum is cheap compared to a Millermatic 180. Probably going to go with the Lincoln 180c. I have an old Solar 2120 which I can no longer get parts for so I'm in the market too. You can buy Tapped pretty cheap used on ebay. They sell on ebay but also have thier own website. I think had some good deals and so does indiana oxyegen(think that was the name). Continous is nicer as can be adjusted more finely however you can save 100$+ going with a Tapped. The only difference you will see in that range of machines is whether it's Tapped or continous wire speed. I sounds like you are looking for around a 140 or 180 so the best bang for your buck IMO is the Lincoln. As was said the Hobart is probably a little cheaper than the equivalent Lincoln and Miller but the Hobarts are also built a little cheaper. I belong to weldingweb and did alot of research on this. I too am in the market for a new mig for home shop use. Hooked my ground cable to the negative terminal had dad hop in the truck when he had the start button pushed i hit the positive post with my electrode worked great never heard a starter turn that fast in my life I run plasmas with it in the feild and I have even started a 24 volt duece and a half with it. She looks like a diesel now when she starts from the fuel being turned up but it has never failed me it is 2005 model Bobcat 250G. They used to only push about 5000-8000 watts on the generator side now they are pushin over 10,500 and my girl is turned up a bit, this last winter when the power was lost from the Ice stoems in KS the old girl powered 2 house through back feeding, each house got two 120 cables into 2 different plug ins ran nonstop for 100 hours. Well the bobcat came a long way in just the past few years. ![]() Once, I tried to run their 220v mig with it and it wouldn't put out enough juice.wierd. Our big engine driven welder/generator is a hobart and it's a really good machine too.īut just the opposite, we used to have a Miller Bobcat at my former job. Depending what you do and what size you get, the hobart may be the better value. Miller and hobart are the same, just the hobart stuff is built slightly cheaper. With the big tank and the cord and everything it was almost $3000 so it's probably more than you are wanting to spend, but if you want to be able to do the really thin and really thick stuff it's the way to go. I also got a 50 foot 220 cord so I could reach farther, think about that if you get a 220 welder. I've ran through a spool and a half of wire already but still have a lot of gas in the tank. I got the big tank since the cost of the refill between the smaller size and that worked out to were the big tank was almost twice as much gas for not much more refill cost. It does just as good on exhaust and thin sheet metal as the 1/2 inch plate. I've welded a lot of thick and thin stuff. I got a Miller 252 last year because I didn't want to overwork a smaller one.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |